How to Prevent Arrow Pass-Through Damage on a Target
Use a denser target or add a layered backstop when arrows pass about 1 inch past the fletching. That usually means the target is too soft, too thin, or too worn for the bow’s draw weight and arrow speed. If you ignore it, shafts bend, fletching gets chewed up, and arrows can drive through the target into the wall or ground behind it. This guide shows how to identify the failure mode, match target material to bow setup, and stop pass-through damage before it starts.
Why is your target failing?

Most target failures come from four causes: the face material is too soft, the bow setup drives more penetration than the target can stop, the target has already channelled, or the arrow setup is putting all the force into one small point. The fix depends on which one is happening, because a full pass-through needs a different response than a ragged, widening hole.
Full pass-through versus partial penetration
A full pass-through means the arrow exits the back of the target, usually with very little slowdown before impact. That raises the risk of shaft damage, lost arrows, and a strike on whatever sits behind the target. Partial penetration means the arrow stops inside the target but buries so deeply that the foam or fill is no longer catching it cleanly.
Deep partial penetration is often the warning sign. If the arrow is entering to the fletching or nearly to the nock, the target is likely close to its limit for that bow and point combination.
What repeated hole enlargement usually means
When the same spot keeps opening up, the target is compressing faster than it can rebound. Foam channels widen, bag fill shifts, and the face no longer closes back around the shaft. That is common when several arrows are grouped tightly or when the target is repeatedly hit in one high-use zone.
Rotation helps only if the target is still structurally sound. Once the opening becomes a tunnel, rotation alone will not bring stopping power back.
Signs the target is already channelled
Channelled targets usually show a few clear signs: arrows slide in too easily, the same lane appears on both face and back, and the target sounds softer in one area than the rest. If the back side shows a straight arrow track, the core has lost enough compression to stop the shot cleanly.
Suppose a 40-pound recurve keeps driving 500-grain arrows deep into one 18-inch foam cube at 15 yards. If the center lane is already visible, the problem is not the yardage alone; the target face has been worn into a path that now guides arrows through the same weak spot.
Target materials and stopping power

Dense foam stops more energy per inch than soft layered foam, but the best choice still depends on draw weight, arrow speed, and tip type. Bag targets are light and weather-friendly, yet they usually stop slower practice arrows better than fast compound setups. Layered block targets sit between those two and often hold up better when impact points move around.
Dense foam versus layered foam
Dense foam targets resist penetration longer because the material compresses under the arrow instead of letting it carve a straight channel. Layered foam works by spreading force across many sheets, which helps with moderate draw weights and field points. If the layers separate early or the face compresses into a lane, stopping power drops fast.
Wear rate matters as much as raw stopping power. A target that stands up well to rain may still wear quickly if it has a soft core and gets repeated hits in the same area. Dense foam often lasts longer indoors, while exposed foam outdoors can age faster under sun and moisture.
Bag targets and layered block targets
Bag targets are useful for beginners and low- to moderate-poundage bows, but they are not the best choice for high-energy compound setups or repeated close-range shooting. Layered block targets handle a wider range of points and usually give better arrow removal than a very tight foam block.
If the goal is to stop damage at the source, a layered block often gives the best balance for mixed practice. It is more forgiving than a bag and less likely to split open than a soft, thin foam face.
Weather resistance and wear rate
Outdoor use changes the failure pattern. Moisture can soften some materials, sunlight can dry and crack others, and freeze-thaw cycles can open small splits into larger channels. A target that survives indoors may lose stopping power much faster outside, especially if it is left uncovered.
When buying or choosing a target, check both weather resistance and wear rate. A target that holds up well in rain is still a poor match if it channels after a few dozen shots from your bow.
How do draw weight and distance change damage?
Higher draw weight increases the chance of pass-through because it sends the arrow faster and with more energy. Shorter shooting distance also matters because the arrow reaches the target with more speed than it would after a longer flight, especially indoors or in a garage where ranges are often short. Matching the target to the bow, not just the distance, is the safer approach.

Beginner compound and recurve draw-weight bands
A common beginner setup is a recurve in the 20 to 30 pound range and a compound in roughly the 15 to 35 pound range for early practice. Those are broad starting points, not target ratings. Once poundage climbs, the target must have enough stopping power for the arrow speed and point type.
Target capacity should match the bow weight the way a backstop must match the bow’s speed and point. If the target is rated well below the setup, partial penetration turns into full pass-through very quickly.
Why shorter distance increases impact energy
Closer distance does not increase the bow’s launch energy, but it does reduce time in flight and can leave the arrow moving faster at impact, especially with light shafts and efficient compounds. In practice, that means a 10-yard shot can hit the face harder than the same setup shot farther back.
Indoor shooting often starts at 10 to 15 yards for beginners. Outdoor practice commonly stretches farther, which can help with control and spread out impacts on the target face. If the target is already soft, though, distance alone will not solve the damage.
When to move back or soften the shot setup
Moving back a few yards can help only if the target is near its limit and the arrow setup is light. A softer setup means a heavier arrow, a lower draw weight, or a more forgiving practice point. Those changes can reduce penetration enough to buy time before replacement.
A common first-timer mistake is moving from 8 yards to 20 yards and expecting the target to stop the arrows better. If the target is too soft for the bow, the safer move is to reduce the impact load or upgrade the target.
Arrow tips and shaft setup
Arrow tip type and shaft setup change how fast a target wears. Field points and bullet points are the usual practice choices because they cut into foam more cleanly and are easier to pull. Broadheads should not be used on most practice targets, since their blades shred foam, open channels, and speed up failure.
Field points and bullet points for practice
Field points are the standard choice for practice targets because their rounded profile limits cutting. Bullet points work in a similar way and are commonly used for general target shooting. Both reduce the chance of torn faces and repeated blowouts compared with sharper hunting heads.
Why broadheads damage most targets fast
Broadheads create a wider wound channel and slice material as they enter. That means more resistance, faster face damage, and a higher chance of punching through softer targets. Even a target that handles field points well can fail quickly if broadheads are used on it repeatedly.
If the arrow is meant for hunting, use a separate practice head or switch to field points for target work. Most practice targets are not built to stop broadheads for long.
How shaft weight and spine affect penetration
Heavier arrows usually fly slower and can reduce penetration risk, which helps on softer targets. They also change the bow’s dynamic reaction and may group differently. Spine mismatch can make the arrow fly poorly, wobble on impact, and strike the target at an angle that creates unpredictable penetration and extra wear.
A badly matched shaft can be as much of a problem as a high draw weight. Poor flight often means the arrow does not enter squarely, and angled impacts can tear a face faster than a clean, straight hit.
Target failure checklist
Use this table to match the symptom to the likely cause and the fix. The goal is to stop the failure mode, not just patch the hole after it gets bigger.
| Symptom | Likely cause | Fix |
|---|---|---|
| Full pass-through | Target too soft for draw weight or arrow speed; worn core; broadhead use | Move to a denser target, reduce bow weight, switch to field or bullet points, and add a rated backstop |
| Deep but not full penetration | Target is near its limit; distance is short; arrow is light or fast | Increase target density, add layered backing, or move to a setup the target is rated for |
| Off-center blowouts | Repeated misses near an edge, poor arrow flight, or a weak seam in layered material | Rotate the target, fix spine mismatch, and inspect the edge for separation or tearing |
| Repeated hole enlargement | Channelled foam, concentrated grouping, or a face that has lost compression | Rotate high-use zones, patch where allowed, flip the face if the design permits, or replace the target |
Target type versus draw-weight band
| Target type | Practical draw-weight band | Notes |
|---|---|---|
| Bag target | Lower-poundage beginner setups | Best with field points; keep distance moderate and avoid broadheads |
| Layered foam target | Low to mid draw weights | Better stopping power than a bag, but can channel if one lane is hit repeatedly |
| Dense foam target | Mid to higher draw weights, depending on rating | More resistant to pass-through if matched to arrow speed and point type |
| Layered block target | Broad beginner-to-intermediate range | Good when shots land across multiple faces and the target rotates often |
What to do when the target is already damaged: stop using the worn face, inspect for hidden arrows, check for loose layers or split seams, and replace the target once channels widen enough that arrows stop cleanly only in untouched areas.
How do you stop pass-throughs with a backstop?
A backstop netting system is the secondary catch layer behind the target. It should be rated for the arrow speed and point type you are shooting, and it should sit far enough behind the target to catch a pass-through without letting the arrow punch straight through the net. In a garage, that usually means giving the net room to flex.
Backstop netting placement behind the target
Place the backstop several feet behind the target, rather than tight against it. That gap lets the arrow slow after any partial pass-through and gives the net room to absorb the shaft. A backstop that is too close can transmit impact back into the target or fail to catch a fast arrow cleanly.
For indoor garages, leave enough space so a miss does not hit the wall if the net stretches. For outdoor yards, make sure the net reaches the full shooting lane width and hangs without gaps along the edges.
Indoor garage setups versus outdoor yards
Indoor setups need a wall-safe plan. Use a rated net or layered backstop behind the target, and keep the shooting lane clear of hard surfaces and stored items. Outdoor setups can use the same netting, but they also need wind stability, secure anchors, and a path that prevents arrows from bouncing into hard ground.
If the target is already worn, a backstop becomes more important, not less. It is the last layer that prevents arrow loss and damage outside the target face.
Safety checks before every shooting session
- Inspect the target face for widening holes, soft spots, and exposed channels.
- Confirm that only field points or bullet points are on practice arrows.
- Check the backstop for tears, loose edges, and proper spacing behind the target.
- Make sure no hidden arrows remain in the target before pulling arrows from the face.
- Verify that the target still matches the bow weight and arrow speed being used.
Frequently asked questions
How do I stop arrows from passing through my target?
Match the target to your draw weight, use field points or bullet points, and move to a denser target if arrows are going more than 1 inch past the fletching. If pass-through still happens, add a rated backstop several feet behind the target and retire any face that has channelled badly.
Why is my target getting damaged by arrows?
Target damage usually comes from too much draw weight, shooting too close for the target’s capacity, using broadheads, or hitting the same area until the foam or fill channels. Worn targets also fail faster because the material no longer rebounds around the shaft after each shot.
What target material stops arrow pass-through best?
Dense foam usually stops pass-through better than soft layered foam or a bag target, especially when the bow has more poundage or the arrows are fast. Layered block targets are a good middle ground for many beginners, while bag targets are best for lower-energy practice setups.
How deep should arrows penetrate a foam target?
There is no single safe depth, but arrows should stop well before the nock on a foam target. If the shaft is burying to the fletching or nearly to the back of the target, the setup is too aggressive for that target and should be changed immediately.
Do field points cause less target damage than broadheads?
Yes. Field points and bullet points are rounded and cut less material on entry, so they are much gentler on practice targets than broadheads. Broadheads slice fibers and foam, which widens holes fast and can turn a usable target into a pass-through risk far sooner.
How do I choose the right target for my draw weight?
Start with the bow’s draw weight, then check the target rating for arrow speed and point type, not just the size. Beginner recurve and compound setups often work with softer targets, but higher-poundage bows need denser foam or layered block construction to stop arrows safely.










