Best Aluminum Arrows for Target Archery (2026): We Compared

Best Aluminum Arrows for Target Archery (2026): We Compared

For target archery, the safest starting point is the Easton Gamegetter Aluminum Arrow Shafts, 500 Spine (12-Pack), because it gives a simple XX75 target shaft to check against Easton’s chart and then fine-tune by cut length and point weight. Easton’s selector still matters most, because the final match depends on actual draw weight, draw length, and your full front-end weight.

Top picks
Our pickEaston Gamegetter Aluminum Arrow Shafts, 500 Spine (12-Pack)

Easton Gamegetter Aluminum Arrow Shafts –⁠ $78.99

Easton Archery · 500 Spine · XX75 Aluminum · 12-Pack
$78.99
Price as of 10 Nov 2026
Drawback: Unfletched bare shafts require additional assembly before shooting.

View on Amazon →

Also greatEaston Genesis XX75 Aluminum Arrows with Diamond Vanes, Silver, 6 Pack

Easton Genesis XX75 Aluminum Arrows with Diamond –⁠ $43.99

Easton · NASP Approved · 7075 Aluminum · 6 Pack
$43.99
Price as of 10 Nov 2026
Drawback: Comes in a smaller 6-pack quantity than standard 12-packs.

View on Amazon →

Budget pickEaston Easton Jazz 1616 Arrow Shafts, 12-Pack

Easton Easton Jazz 1616 Arrow Shafts, 12-Pack –⁠ $50.41

Easton · Jazz 1616 · Aluminum Alloy · 12-Pack
$50.41
Price as of 10 Nov 2026
Drawback: Components are sold separately for these unfletched shafts.

View on Amazon →

As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

Quick comparison

ProductBadgeBest forPrice
Easton Gamegetter Aluminum Arrow Shafts, 500 Spine (12-Pack)Easton Gamegetter Aluminum Arrow Shafts, 500 Spine (12-Pack)Easton ArcheryOur pick500 Spine · XX75 Aluminum · 12-Pack$78.99

Price as of 10 Nov 2026
View
Easton Genesis XX75 Aluminum Arrows with Diamond Vanes, Silver, 6 PackEaston Genesis XX75 Aluminum Arrows with Diamond VanesEastonAlso greatNASP Approved · 7075 Aluminum · 6 Pack$43.99

Price as of 10 Nov 2026
View
Easton Easton Jazz 1616 Arrow Shafts, 12-PackEaston Easton Jazz 1616 Arrow Shafts, 12-PackEastonBudget pickJazz 1616 · Aluminum Alloy · 12-Pack$50.41

Price as of 10 Nov 2026
View
As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

Use the selector when you need a chart check before buying a dozen and want to start from actual bow measurements. Use the XX75-style target shafts when you already know your setup and want common indoor aluminum options that are easy to sort by code.

How we chose

These picks focus on target-only use, not hunting shafts. They also fit a manual workflow that starts with measured bow weight, cut length, and point-plus-insert weight, then checks the result against Easton’s current guidance.

Chart clarity mattered too. A good target aluminum guide must let an archer move from draw weight and cut length to a shaft family without guessing, then confirm the final choice against the manufacturer chart.

Tuning margin mattered as well. Aluminum target shafts need enough room to absorb point-weight changes, longer cuts, and recurve-versus-compound differences without sending the archer into a dead end.

Verification was the last filter. No page can replace the manufacturer chart, so each recommendation had to support a final check rather than pretend to be the last word.

Easton aluminum arrow selector: best for chart checking

Key points: Easton aluminum arrow selector: best for chart checking
As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

This is the best fit for archers who want Easton’s current guidance before ordering target arrows. Easton’s target selector includes recurve and compound bow types, and it also includes an aluminum arrows option for target shooting.

The selector asks for actual draw weight, draw length, and an aluminum shaft choice. That matters because shaft choice should come from the bow you actually shoot, not from a guessed poundage or a label on the riser.

The strongest point here is the workflow. Measure the bow, enter the setup, then cross-check the resulting shaft family against your cut length and point weight before you buy.

The drawback is simple: a selector is not a finished setup. It still needs a manual check, especially if your arrow length is long, your point is heavy, or your indoor setup uses extra front-end weight.

Easton Gamegetter Aluminum Arrow Shafts, 500 Spine: best for chart checking

Key points: Easton Gamegetter Aluminum Arrow Shafts, 500 Spine: best for chart checking
As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

This is a solid target shaft choice for archers who already have a likely spine range and want a straightforward XX75 aluminum option to compare against the chart. The published details point to precision-drawn XX75 aluminum, 7075-T9 alloy, and plus or minus .003 inch straightness.

It suits shooters who want a clean test set for outdoor target work or for comparing a known shaft code against Easton’s guidance. The 500 spine label is also useful as a reference point when you are checking whether your setup wants stiffer or weaker behavior.

The drawback is that a 500 spine alone does not tell the whole story. Cut length and point weight can still move the final result, so it should be checked against the chart instead of treated as a universal answer.

Easton Easton Jazz 1616 Arrow Shafts, 12-Pack: best for indoor target shafts

As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

This is the better fit for archers who want a large-diameter target aluminum shaft with a beginner-friendly setup. The published details point to 7075 aerospace aluminum alloy and plus or minus .005 inch straightness, which makes it a practical indoor target reference.

It fits the common target aluminum pattern better than a hunting-style shaft because the 1616 code is part of the familiar 4-digit aluminum system. For indoor work, that makes it easy to compare with other XX75-family codes such as 2016, 2117, and 2315 when you are sorting by chart.

The drawback is that this is not a one-size answer for every recurve or compound setup. A longer cut, heavier point, or stronger bow can push the final choice away from 1616, so the chart still decides the last step.

What aluminum arrow spine should I use for target archery?

Start with the shaft code that matches your measured bow weight, arrow length, and front-end weight, then verify it against Easton’s chart. For target archery, aluminum is common, lower spine numbers mean stiffer arrows, and a wrong match usually shows up as poor grouping or erratic flight.

For a manual check, think in bands rather than guesses. A target recurve often ends up one size weaker than a compound with the same peak draw weight, because the setup and energy delivery are different.

Quick rule for target setups

Use the chart first, not after the purchase. If the arrow is cut longer or the point gets heavier, expect the dynamic spine to act weaker and move toward a stiffer shaft code.

How do I read an Easton aluminum arrow spine chart

Read the chart from measured bow weight and cut length, then check the recommended aluminum shaft code. Easton’s selector uses actual draw weight and draw length, and its aluminum option is meant for target shooters who want current guidance rather than guesswork.

Do not treat the 4-digit code like a carbon-style spine number. In Easton’s aluminum naming, the first two digits are used for shaft diameter in 1/64 inch and the last two digits for wall thickness in 1/1000 inch; examples include codes such as 2016, 2117, and 2315.

Static spine versus dynamic spine

Static spine is the shaft’s measured deflection under test conditions: an 880-gram weight, a 29-inch shaft, supported 28 inches apart, with the deflection multiplied by 1,000. Easton says 500 spine bends half an inch under standard test conditions.

Dynamic spine is the spine your bow actually makes happen in flight. It changes with bow energy, point weight, arrow length, and setup variables, so two arrows with the same code can behave differently on different target bows.

Which aluminum arrow size is right for my draw weight and arrow length?

Choose the size that matches your actual measured draw weight at your draw length, then adjust for cut length. Longer arrows need stiffer shafts, shorter arrows can use weaker shafts, and Easton says shortening the arrow can make dynamic spine act stiffer.

Key points: Which aluminum arrow size is right for my draw weight and arrow length?

A practical target rule is to sort by draw-weight band first, then move the code one step stiffer if the arrow is long or the front-end weight is heavy. Do not skip the cut-length check, because length changes can move the result enough to miss the center of the target.

Manual aluminum spine cross-check table

Common target aluminum codePractical use bandArrow-length adjustmentPoint-weight sensitivityToo weak or too stiff?
1816Light target recurve or lower-poundage setup with standard indoor or outdoor target useWorks better when cut shorter; long cuts push it weaker fastMore sensitive to heavier points and insertsIf the shaft kicks weak or groups open left for a right-handed archer, move stiffer. If it reacts harsh and lands right, it may be too stiff.
1916Middle band for moderate target recurve use and lighter compound target setupsAccepts moderate length, but a longer shaft still weakens itMedium sensitivity; heavier points can move it out of tuneWeak tears or soft tail movement suggest too weak. Hard, fast left impact can point to too stiff.
2016Common target band for many recurve setups and some lighter compound target setupsGood starting point at moderate cut lengthPoint weight matters a lot, especially for indoor target pointsIf your grouping breaks down after adding front weight, step stiffer. If the shaft feels too hard to tune, step weaker.
2114Useful when the setup wants a bit more stiffness than 2016 but not a full jump to a much stiffer shaftHandles shorter to medium cuts better than long cutsModerate sensitivity to point changesIf broad tuning data shows the arrow behaving weak, move stiffer. If it tunes with little effort and still feels soft, stay here or go stiffer only if the chart asks for it.
2117Heavier target recurve, many indoor target setups, and some compound target setups with more peak draw weightBetter for medium-length shafts than extended cutsStill reacts to point and insert weight, but tolerates more front-end mass than weaker shaftsIf the shaft still acts weak after shortening and lighter points, go stiffer. If it refuses to tune and shows a hard reaction, it may be too stiff.
2219Strong target band for higher poundage indoor setups and larger-diameter target buildsBest when the cut length is controlled, not stretched longLess forgiving of heavy front-end changes than lighter shaftsWeak if the shaft flexes too much on release; stiff if the bow never gets a clean tune with normal point weight.
2315Large-diameter target shaft band for strong indoor target setups and heavier front-end useCan still weaken with longer cuts, but it starts from a stiffer baselinePoint weight still matters, though the shaft begins stiffer than 2016 or 2117If you are already on the edge of too weak with a long cut, move stiffer or shorten the shaft. If it feels harsh and over-stiff, move weaker only if the chart allows it.

Say your recurve is set for a moderate target weight and the cut arrow is long from throat to shaft end. The extra length weakens the dynamic spine, so the same code may need a stiffer band than the chart’s shortest-cut example.

Suppose a compound shooter adds a heavier indoor point. That extra front-end weight weakens dynamic spine, so a shaft that looked correct on paper can start acting soft once the point and insert are installed.

Does point weight change aluminum arrow spine for target shooting?

Yes. Heavier point weight weakens dynamic spine, and Easton says reducing point weight can make dynamic spine act stiffer. The same shaft code can therefore behave differently once the point and insert are added to the front end.

Archery Supplier lists 100 grains as a common standard point weight assumption, and Naptyme advises measuring poundage, arrow length, and combined point/insert weight. That combined front-end weight matters more than point weight alone.

Point weight and insert weight in practice

A target arrow with a heavier point and insert will flex more on release. That can help a shaft that is too stiff, but it can also push a borderline shaft too weak if the cut is long.

What aluminum arrow spine is best for a recurve target bow?

For a recurve target bow, start with the Easton chart using actual draw weight and arrow length, then expect to land slightly weaker than a compound of the same peak draw weight. Recurve setups often accept aluminum target shafts well, but the final code still depends on point weight and cut length.

Do not guess from the bow label alone. The measured bow weight matters more than the printed poundage when you are deciding between neighboring codes such as 1916, 2016, and 2117.

Recurve adjustment logic

If a recurve arrow groups weak, shorten the shaft first if you have room. If it still tunes soft, move stiffer. If the shaft feels harsh or hard to tune, move weaker only after checking the chart again.

How much does a longer arrow weaken aluminum spine?

A longer arrow weakens dynamic spine because the shaft has more unsupported length in flight. The same source notes that adding one inch of arrow length can weaken spine by about one step, so cut length is not a minor detail.

This is why a shaft that looks right at a short test length can go soft after a longer build. Easton also says shortening the arrow can make dynamic spine act stiffer, which is the opposite direction.

How do I confirm my aluminum arrow choice before buying a full dozen?

Confirm it by checking the manufacturer chart, then buying a small test set or matching your current arrows to the same measured setup. Use actual draw weight, draw length, cut length, and combined point-plus-insert weight before you order a full dozen.

A good check is to compare the chart result with your manual cross-check table on this page. If the setup sits near a boundary, move one size stiffer or weaker only after you see how length and front-end weight shift the result.

Which one should you buy?

Choose the Easton aluminum selector first if you need a chart check before buying a dozen and you want to work from actual bow measurements. It is the clearest tool for recurve and compound target archers who do not want to guess.

Choose the Easton Gamegetter 500 Spine when you want a clean XX75 target shaft to compare against your chart or a reference point for a known setup. Choose the Easton Jazz 1616 when your target setup points toward a large-diameter indoor aluminum shaft and you want a familiar target code to start from.

Use measured bow weight, not a guess, before ordering anything. If the arrow is long or the point weight is heavy, move one step stiffer; if the chart already lands you near a soft boundary, shorten first before changing families.

A common first-timer mistake is to shop by bow poundage alone and ignore cut length. Another is to add heavy indoor points and keep the same shaft code without rechecking dynamic spine.

Keep reading

Frequently asked questions

How do I choose between 2016, 2114, and 2315 aluminum arrows?

Choose 2016 for a common middle target band, 2114 when you need a bit more stiffness, and 2315 when the setup calls for a stronger large-diameter target shaft. The final answer still depends on measured bow weight, cut length, and point-plus-insert weight.

Similar Posts